-
Build finished. Ready for balancing and maiden.
Build finished. Ready for balancing and maiden.
Build finished. Ready for balancing and maiden.
-
Build finished. Ready for balancing and maiden.
Build finished. Ready for balancing and maiden.
Build finished. Ready for balancing and maiden.
-
Build finished. Ready for balancing and maiden.
Build finished. Ready for balancing and maiden.
Build finished. Ready for balancing and maiden.
-
Build finished. Ready for balancing and maiden.
Build finished. Ready for balancing and maiden.
Build finished. Ready for balancing and maiden.
-
Build finished. Ready for balancing and maiden.
Build finished. Ready for balancing and maiden.
Build finished. Ready for balancing and maiden.
-
Partially built wing resting on fuselage.
Partially built wing resting on fuselage.
Partially built wing resting on fuselage.
-
Partially built wing resting on fuselage.
Partially built wing resting on fuselage.
Partially built wing resting on fuselage.
-
Partially built wing resting on fuselage.
Partially built wing resting on fuselage.
Partially built wing resting on fuselage.
-
Fuselage with tail set on it.
Fuselage with tail set on it.
Fuselage with tail set on it.
-
Fuselage with tail set on it.
Fuselage with tail set on it.
Fuselage with tail set on it.
-
Fuselage covered
Fuselage covered
Fuselage covered
-
Fuselage covered
Fuselage covered
Fuselage covered
-
Fuselage covered.
Fuselage covered.
Fuselage covered.
-
Squaring up the horizontal stabaliser using pins and thread.
Squaring up the horizontal stabaliser using pins and thread.
Squaring up the horizontal stabaliser using pins and thread.
-
Squaring up the horizontal stabaliser using pins and thread.
Squaring up the horizontal stabaliser using pins and thread.
Squaring up the horizontal stabaliser using pins and thread.
-
Horizontal stabaliser build in progress.
Horizontal stabaliser build in progress.
Horizontal stabaliser build in progress.
-
Horizontal stabaliser.
Horizontal stabaliser.
Horizontal stabaliser.
-
Drilling holes for the hinge screws with the ArrowMax pen drill.
Drilling holes for the hinge screws with the ArrowMax pen drill.
Drilling holes for the hinge screws with the ArrowMax pen drill.
-
1.6mm nut. A dab of glue on the end of a balsa cutoff holds the tiny nut perfectly for attaching to the screw.
1.6mm nut. A dab of glue on the end of a balsa cutoff holds the tiny nut perfectly for attaching to the screw.
1.6mm nut. A dab of glue on the end of a balsa cutoff holds the tiny nut perfectly for attaching to the screw.
-
Fixing hinge screws.
Fixing hinge screws.
Fixing hinge screws.
-
Squaring up the horizontal stabaliser using pins and thread.
Squaring up the horizontal stabaliser using pins and thread.
Squaring up the horizontal stabaliser using pins and thread.
-
Squaring up the horizontal stabaliser using pins and thread.
Squaring up the horizontal stabaliser using pins and thread.
Squaring up the horizontal stabaliser using pins and thread.
-
Squaring up the horizontal stabaliser using pins and thread.
Squaring up the horizontal stabaliser using pins and thread.
Squaring up the horizontal stabaliser using pins and thread.
-
Vertical stabaliser.
Vertical stabaliser.
Vertical stabaliser.
-
Vertical stabaliser.
Vertical stabaliser.
Vertical stabaliser.
-
Vertical stabaliser in progress.
Vertical stabaliser in progress.
Vertical stabaliser in progress.
-
Battery compartment.
Battery compartment.
Battery compartment.
-
Fuselage front section.
Fuselage front section.
Fuselage front section.
-
Fuselage rear section.
Fuselage rear section.
Fuselage rear section.
-
Fuselage rear section.
Fuselage rear section.
Fuselage rear section.
-
Fuselage rear section.
Fuselage rear section.
Fuselage rear section.
-
Fuselage rear section.
Fuselage rear section.
Fuselage rear section.
-
Fuselage, wing centre section and a bit of the port wing end.
Fuselage, wing centre section and a bit of the port wing end.
Fuselage, wing centre section and a bit of the port wing end.
-
Elevator and rudder servos.
Elevator and rudder servos.
Elevator and rudder servos.
-
Fuselage front section.
Fuselage front section.
Fuselage front section.
-
Wing centre section. The centre section is too long for my building board so I am going to have to build it in bits.
Wing centre section. The centre section is too long for my building board so I am going to have to build it in bits.
Wing centre section. The centre section is too long for my building board so I am going to have to build it in bits.
-
Wing centre section. The centre section is too long for my building board so I am going to have to build it in bits.
Wing centre section. The centre section is too long for my building board so I am going to have to build it in bits.
Wing centre section. The centre section is too long for my building board so I am going to have to build it in bits.
-
Port wing end built.
Port wing end built.
Port wing end built.
-
Fuselage sides.
Fuselage sides.
Fuselage sides.
-
Some fuselage parts: sides, floor, bulkheads and battery tray.
Some fuselage parts: sides, floor, bulkheads and battery tray.
Some fuselage parts: sides, floor, bulkheads and battery tray.
-
Starting to build the port wing end.
Starting to build the port wing end.
Starting to build the port wing end.
-
First batch of Balsa and Ply paers laser cut.
First batch of Balsa and Ply paers laser cut.
First batch of Balsa and Ply paers laser cut.